View MIC23050_4464904.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC23050 4mhz pwm buck regulator with hyperlight load? switching scheme y, inc. protected by us patent no. 7064531 l +1 ( 408 ) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com hyperlight load is a trademark of micrel, inc. mlf and micro leadframe are registered trademarks of amkor technolog micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? te september 2011 general description the micrel MIC23050 is a high-efficiency, 600ma, pwm, synchronous buck (step-down) regulator featuring the hyperlight load? patented swit ching scheme that offers best-in-class light load efficiency and transient performance while providing very-small external components and low output ripple at all loads. the MIC23050 also has a very-low typical quiescent current draw of 20a and can achieve over 89% efficiency even at 1ma. the device allows operation with a tiny inductor ranging from 0.47h to 2.2h and uses a small output capacitor that enables a sub-1mm height. in contrast to traditional light load schemes, the hyperlight load? architecture does not need to trade off control speed to obtain low standby currents and in doing so the device only needs a small output capacitor to absorb the load transient as the powered device goes from light load to full load. at higher loads the MIC23050 provides a constant switching frequency of greater than 4mhz while providing peak efficiencies greater than 93%. the MIC23050 comes in fixed output voltage options from 0.72v to 3.3v eliminating external feedback components. the MIC23050 is available in an 8-pin 2mm x 2mm mlf ? with a junction operating range from ?40 c to +125 c. datasheets and support documentation can be found on micrel?s web site at: www.micrel.com . features ? input voltage: 2.7v to 5.5v hyperlight load? ? 600ma output current ? fixed output voltage from 0.72v to 3.3v ? ultra-fast transient response ? 20a typical quiescent current ? 4mhz in pwm in constant-current mode ? 0.47h to 2.2h inductor ? low voltage output ripple ? 25mv pp in hyperlight load? mode ? 3mv output voltage ripple in full pwm mode ? >93% efficiency ? ~89% at 1ma ? micropower shutdown ? available in 8-pin 2mm x 2mm mlf ? ? ?40 c to +125 c junction temperature range applications ? cellular phones ? digital cameras ? portable media players ? wireless lan cards ? wifi/wimax/wibro modules ? usb-powered devices ____________________________________________________________________________________________________________ typical application 1 m9999-092211-e
micrel, inc. MIC23050 september 2011 2 m9999-092211-e ordering information part number marking nominal output voltage (1) junction temperature range package (2) lead finish MIC23050-cyml gkc 1.0v ?40 to +125c 8-pin 2x2 mlf ? pb-free MIC23050-4yml gk4 1.2v ?40 to +125c 8-pin 2x2 mlf ? pb-free MIC23050-gyml gkg 1.8v ?40 to +125c 8-pin 2x2 mlf ? pb-free MIC23050-syml gks 3.3v ?40 to +125c 8-pin 2x2 mlf ? pb-free notes 1. other output voltage options available (0. 72v to 3.3v), contact micrel for details. 2. mlf ? is a green rohs compliant package. lead fini sh is nipdau. mold compound is halogen free. pin configuration 1sw en nc sns 8 pgnd vin agnd cff 7 6 5 2 3 4 8-pin 2mm x 2mm mlf ? (ml) (top view) pin description pin number pin name pin name 1 sw switch (output): internal power mosfet output switches. 2 en enable (input). logic low will shut down the device, reducing the quiescent current to less than 4a. do not leave floating. 3 nc no connect. 4 sns connect to v out to sense output voltage. 5 cff feed forward capacitor. connect a 560pf capacitor from v out to cff pin. 6 agnd analog ground. 7 vin supply voltage (input): r equires bypass capacitor to gnd. 8 pgnd power ground.
micrel, inc. MIC23050 september 2011 3 m9999-092211-e absolute maximum ratings (1) supply voltage (v in ) .........................................................6v output switch voltage (v sw ) ............................................6v output switch current (i sw )..............................................2a logic input voltage (v en , v lq )........................... v in to ?0.3v junction temperature (t j ) ....................................... + 150 c storage temperature range (t s )..............?65c to +150c esd rating (3) .................................................................. 3kv operating ratings (2) supply voltage (v in )......................................... 2.7v to 5.5v logic input voltage (v en ) ....................................... 0v to v in junction temperature (t j ) ..................?40c t j +125c thermal resistance 2mm x 2mm mlf-8 ( ja ) ...................................90c/w 2mm x 2mm mlf-8 ( jc ) ...................................45c/w electrical characteristics (4) t a = 25 c with v in = v en = 3.6v; l = 1h; c ff = 560pf; c out = 4.7f; i out = 20ma unless otherwise specified. bold values indicate ?40c t j +125c. parameter condition min. typ. max. units supply voltage range 2.7 5.5 v undervoltage lockout threshol d (turn-on) 2. 45 2.55 2.65 v uvlo hysteresis 100 mv quiescent current, hyper ll mode i out = 0ma , v sns > 1.2*v out nominal 20 32 a shutdown current v in = 5.5v; v en = 0v; 0.01 4 a output voltage accuracy v in = 3.0v, i load = 20ma ?2.5 +2.5 % current limit in pwm mode sns = 0.9*v nom 0.65 1 1.7 a output voltage line regulation v in = 3.0v to 5.5v, i load = 20ma 0.5 %/v output voltage load regulation 20ma < i load < 500ma, 0.3 % maximum duty cycle sns v nom 80 89 % pwm switch on-resistance i sw = 100ma pmos i sw = ? 100ma nmos 0.45 0.5 ? ? frequency i load = 120ma 3.4 4 4.6 mhz soft-start time v out = 90% 650 s enable threshold (turn-on) 0.5 0.8 1.2 v enable hysteresis 35 mv enable input current 0.1 2 a over-temperature shutdown 165 c over-temperature shutdown hysteresis 20 c notes: 1. exceeding the absolute maximum rating may damage the device. 2. the device is not guaranteed to function outside its operating rating. 3. devices are esd sensitive. handling precautions recommended. human body model, 1.5k ? in series with 100pf. 4. specification for packaged product only.
micrel, inc. MIC23050 september 2011 4 m9999-092211-e typical characteristics
micrel, inc. MIC23050 september 2011 5 m9999-092211-e typical characteristics (continued)
micrel, inc. MIC23050 september 2011 6 m9999-092211-e functional characteristics
micrel, inc. MIC23050 september 2011 7 m9999-092211-e functional characteristics (continued)
micrel, inc. MIC23050 september 2011 8 m9999-092211-e functional diagram en vin sw pgnd cff control logic timer & softstart isense agnd uvlo reference gate drive sns error comparator current limit zero 1 MIC23050 simplified block diagram
micrel, inc. MIC23050 september 2011 9 m9999-092211-e functional description vin vin provides power to the mosfets for the switch mode regulator section and to the analog supply circuitry. due to the high switching speeds, it is recommended that a 2.2f or greater capacitor be plac ed close to vin and the power ground (pgnd) pin for bypassing. refer to the layout recommendations for details. en the enable pin (en) controls the on and off state of the device. a logic high on the enable pin activates the regulator, while a logic low deactivates it. MIC23050 features built-in soft-start circuitry that reduces in-rush current and prevents the output voltage from overshooting at start up. do not leave this pin floating. sw the switch (sw) pin connects directly to the inductor and provides the switching current necessary to operate in pwm mode. due to the high speed switching on this pin, the switch node should be rout ed away from sensitive nodes such as the cff pin. sns an inductor is connected from the sw pin to the sns pin. the sns pin is the output pin of the device and a minimum of 2.2f bypass capacitor should be connected in shunt. in order to reduce parasitic i nductance it is good practice to place the output bypass capacitor as close to the inductor as possible. cff the cff pin is connected to the sns pin of MIC23050 with a feed-forward capacitor of 560pf. the cff pin itself is compared with the internal reference voltage (v ref ) of the device and provides the co ntrol path to control the output. v ref is equal to 0.72v. the cff pin is sensitive to noise and should be place away from the sw pin. refer to the layout recommendations for details. pgnd power ground (pgnd) is the ground path for the high current pwm mode. the current loop for the power ground should be as small as possible and separate from the analog ground (agnd) loop. refer to the layout recommendations for more details. agnd signal ground (agnd) is the ground path for the biasing and control circuitry. the current loop for the signal ground should be separate from the power ground (pgnd) loop. refer to the layout recommendations for more details.
micrel, inc. MIC23050 september 2011 10 m9999-092211-e applications information input capacitor a minimum of 2.2f ceramic capacitor should be placed close to the vin pin and pgnd pin for bypassing. x5r or x7r dielectrics are recommended for the input capacitor. y5v dielectrics, aside from losing most of their capacitance over temperature, they also become resistive at high frequencies. this redu ces their ability to filter out high frequency noise. output capacitor the MIC23050 is designed for use with a 2.2f or greater ceramic output capacitor. a low equivalent series resistance (esr) ceramic output capacitor either x7r or x5r is recommended. y5v and z5u dielectric capacitors, aside from the undesirable effect of their wide variation in capacitance over temperature, become resistive at high frequencies. inductor selection inductor selection will be determined by the following (not necessarily in the order of importance); ? inductance ? rated current value ? size requirements ? dc resistance (dcr) the MIC23050 is designed for use with an inductance range from 0.47h to 2.2h. typically, a 1h inductor is recommended for a balance of transient response, efficiency and output ripple. for faster transient response a 0.47h inductor may be used. for lower output ripple, a 2.2h is recommended. maximum current ratings of the inductor are generally given in two methods; permissible dc current and saturation current. permissible dc current can be rated either for a 40c temperature rise or a 10% to 20% loss in inductance. ensure the inductor selected can handle the maximum operating current. when saturation current is specified, make sure that t here is enough margin so that the peak current of the induct or does not cause it to saturate. peak current can be calculated as follows: i pk = i out + v out (1-v out /v in )/2fl as shown by the previous ca lculation, the peak inductor current is inversely proportional to the switching frequency and the inductance; the lower the switching frequency or the inductance the higher the peak current. as input voltage increases the peak current also increases. the size of the inductor depends on the requirements of the application. refer to the application circuit and bill of material for details. dc resistance (dcr) is al so important. while dcr is inversely proportional to size, dcr can represent a significant efficiency loss. refer to the efficiency considerations. compensation the MIC23050 is designed to be stable with a 0.47h to 2.2h inductor with a 2. 2f ceramic (x5r) output capacitor. efficiency considerations efficiency is defined as the am ount of useful output power, divided by the amount of power supplied: 100 iv iv % efficiency inin out out ? ? ? ? ? ? ? ? = maintaining high efficiency serves two purposes. it reduces power dissipation in the power supply, reducing the need for heat sinks and ther mal design considerations and it reduces consumption of current for battery powered applications. reduced current draw from a battery increases the devices operating time and is critical in hand held devices. there are two types of losses in switching converters; dc losses and switching losses. dc losses are simply the power dissipation of i 2 r. power is dissipated in the high side switch during the on cycle. power loss is equal to the high side mosfet r dson multiplied by the switch current 2 . during the off cycle, the low side n-channel mosfet conducts, also dissipating power. device operating current also reduces efficiency. the product of the quiescent (operating) current and the supply voltage is another dc loss. the current re quired driving the gates on and off at a constant 4mhz frequency and the switching transitions make up the switching losses.
micrel, inc. MIC23050 september 2011 11 m9999-092211-e hyperlight load mode? MIC23050 uses a minimum on and off time proprietary control loop. when the output voltage falls below the regulation threshold, the error comparator begins a switching cycle that turns the pmos on and keeps it on for the duration of the minimu m-on-time. when the output voltage is over the regulation threshold, the error comparator turns the pmos off for a minimum-off-time. the nmos acts as an ideal rectifier that conducts when the pmos is off. using a nmos switch instead of a diode allows for lower voltage drop across the switching device when it is on. the asynchronous switching combination between the pmos and the nmos allows the control loop to work in discontinuous mode for light load operations. in discontinuous mode MIC23050 works in pulse frequency modulation (pfm) to regulate the output. as the output current increases, the switching frequency increases. this improves the efficiency of MIC23050 during light load currents. as the load current increases, the MIC23050 goes into continuous conduction mode (ccm) at a constant frequency of 4mhz. the equation to calculate the load when the MIC23050 goes into continuous conduction mode may be approximated by the following formula: figure 1. MIC23050 efficiency curve figure 1 illustrates an efficiency curve for the MIC23050. from no load to 100ma, efficiency losses are dominated by quiescent current loss es, gate drive and transition losses. by using the hyperlight load ? mode the MIC23050 is able to maintain high efficiency at low output currents. ? ? ? ? ? ? ? = f2l d)v(v i out in load over 100ma, efficiency loss is dominated by mosfet rdson and inductor losses. higher input supply voltages will increase the gate-to-source threshold on the internal mosfets, reducing the internal rdson. this improves efficiency by reducing dc losses in the device. all but the inductor losses are inherent to the device. in which case, inductor selection becomes increasingly critical in efficiency calculations. as the inductors are reduced in size, the dc resistance (dcr) can become quite significant. the dcr losses can be calculated as follows: l pd = i out 2 dcr from that, the loss in efficiency due to inductor resistance can be calculated as follows: 100 pd liv iv 1loss efficiency out out out out ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? + ?= efficiency loss due to dcr is minimal at light loads and gains significance as the load is increased. inductor selection becomes a trade-off between efficiency and size in this case.
micrel, inc. MIC23050 september 2011 12 m9999-092211-e MIC23050 typical application circuit
micrel, inc. MIC23050 september 2011 13 m9999-092211-e bill of materials item part number manufacturer description qty. c1, c2 c1608x5r0j475k tdk (1) 4.7f ceramic capacitor, 6.3v, x5r, size 0603 2 c3 c1608c0g1h561j tdk (1) 560pf ceramic capacitor, 50v, npo, size 0603 1 lqm21pn1r0mc0d murata (2) 1h, 0.8a, 190m ? , l2mm x w1.25mm x h0.5mm lqh32cn1r0m33 murata (2) 1h, 1a, 60m ? , l3.2mm x w2.5mm x h2.0mm lqm31pn1r0m00 murata (2) 1h, 1.2a, 120m ? , l3.2mm x w1.6mm x h0.95mm glf251812t1r0m tdk (1) 1h, 0.8a, 100m ? , l2.5mm x w1.8mm x h1.35mm lqm31pnr47m00 murata (2) 0.47h, 1.4a, 80m ? , l3.2mm x w1.6mm x h0.85mm l1 mipf2520d1r5 fdk (3) 1.5h, 1.5a, 70m ? , l2.5mm x w2mm x h1.0mm 1 u1 MIC23050-xyml micrel, inc. (4) 4mhz pwm buck regulator with hyperlight load? mode 1 notes: 1. tdk: www.tdk.com . 2. murata: www.murata.com . 3. fdk: www.fdk.co.jp . 4. micrel, inc: www.micrel.com .
micrel, inc. MIC23050 september 2011 14 m9999-092211-e pcb layout recommendations top layer bottom layer
micrel, inc. MIC23050 september 2011 15 m9999-092211-e package information 8-pin 2mm x 2mm mlf ? (ml) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. this information is not intended as a warranty and micrel does not assume responsibility for it s use. micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. no license, whether express, implied, arising by estoppel or other wise, to any intellectual property rights is granted by this document. except as provided in micrel?s terms and conditions of sale for such products, mi crel assumes no liability whatsoever, and micrel disclaims any express or implied warranty relating to the sale and/or use of micrel products including l iability or warranties relating to fitness for a particular purpose, merchantability, or infringement of an y patent, copyright or other intellectual p roperty right. micrel products are not designed or authorized for use as components in life suppor t appliances, devices or systems where malfu nction of a product reasonably be expected to result in pers onal injury. life support devices or system s are devices or systems that (a) are in tended for surgical impla into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significan t injury to the user. a purchaser?s use or sale of micrel produc ts for use in life support app liances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. can nt ? 2007 micrel, incorporated.

▲Up To Search▲

Price & Availability of MIC23050

	To Download MIC23050 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .